NAND

The iQue uses a 64MiB NAND flash, which consists of 4096 logical blocks of 16384 bytes each (made up of 32 512-byte pages)

Each page also has 16 bytes of spare data, which is used for bad-block markers, error-correction codes and block-pointers for the SA area.

Unfortunately the I@H USB commands for reading/writing NAND can only access the last page-spare of each block, though hardware NAND writers can access all of them.

Block Map

• 0x0 - 0x40 - SKSA area, marked in the BBFS FAT as reserved
• 0x40 - 0xFF0 - data area, used for files in the BBFS
• 0xFF0 - 0x1000 - BBFS area, each block holds a copy of the BBFS along with a 'sequence number', highest sequence number is the latest BBFS.

BBFS

BBFS is the filesystem used on the iQue NAND, a very simple file-system used to store games and config data. The Wii NAND's SFFS is actually very similar to BBFS, though with many more features.

The BBFS is made up of three parts: a FAT (file-allocation table), an entry table and a footer:

FAT

The FAT is located at 0x0 in the BBFS block, made up of 4096 16-bit signed integers, one for each block in the NAND. This is used to specify if a block may be reserved, bad, available, or it might point to another block in the 'chain' (ie. file 0 points to block 0, block 0 points to block 2, block 2 points to block 15...), or signify the end of the chain.

Files make use of the FAT by simply pointing to a block in the FAT as its start block. Extracting the file is then just a matter of following the chain of pointers in the FAT, reading in each block until you reach an end-of-chain marker.

Possible FAT entries:

Value	Description
0	Free/unused block
-1	End-of-chain marker
-2	Bad block
-3	Reserved block (used for SKSA area)

Entry Table

File entries are stored from 0x2000 - 0x3FF4 in the BBFS block, allowing for 409 entries per BBFS.

Each entry has the format:

Offset	Length	Type	Information
0x0	0x8	char	File name
0x8	0x3	char	File extension
0xB	0x1	byte	Valid indicator (1 if file is valid)
0xC	0x2	int16	Start block #
0xE	0x2	bytes	Padding?
0x10	0x4	int32	File size

Files may be deleted by simply having the Valid indicator set to 0, or having a block number of -1, so when reading the entry table you should make sure to read all 409 entries first and then filter out any invalid ones.

Footer

From 0x3FF4 to 0x4000 is the BBFS footer, which simply contains a BBFS signature to identify it as a BBFS block, a sequence number used for finding the latest BBFS, and a checksum for verifying the BBFS contents.

Offset	Length	Type	Information
0x0	0x4	char	Magic (BBFS or BBFL)
0x4	0x4	int32	Sequence number
0x8	0x2	int16	Link block #
0xA	0x2	int16	Checksum

The "Link block #" field seems to be used for linking two BBFS blocks together, though this hasn't been seen in any NAND dumps so far (maybe meant for NANDs larger than 4096 blocks, or containing more than 409 entries?).

Checksum is a basic adder, the fields value is made by adding each uint16 from 0x0 - 0x3FFE, and taking the result away from 0xCAD7. For verifying, 0x0 - 0x4000 is added together, and if the result is 0xCAD7 the checksum is valid.